MotionCam Outdoor PhOD

Lightning-fast alarms. Verified.

MotionCam Outdoor recognizes intrusion from the very first steps on the territory and confirms it with an animated series of photos. Visual verification helps to instantly ascertain the situation, saving users from concerns, and security companies from unnecessary patrol dispatches.

1. Motion detected
2. Alarm raised 
3. Evidence captured
4.  

Don't miss a thing

Combining the best optics, fast processor and advanced software algorithms, MotionCam Outdoor takes informative pictures in any weather, day or night.

Camera designed to guard

An outdoor camera often has to shoot in difficult lighting conditions. Direct sunlight, reflective surfaces, or street lights can blind the camera, depriving the image of critical details. This is unacceptable for a security device. We were challenged to get a clear and sharp image that would confirm intrusion in seconds and allow security companies to react in time.

Quality is in the details

We have rejected plastic optics to make a waterproof lens out of glass and metal. The wide-angle lens covers the entire protected area, giving a complete picture of what is happening. In bright light, an infrared filter is automatically applied to ensure distortion-free color reproduction, and two bright IR LEDs help to see the intruder even in total darkness.

HDR

To take one photo, MotionCam Outdoor takes two consecutive shots at long and short exposures. The processor instantly combines the shots, equalizing the balance between light and dark areas of the image, and then compresses it for the fastest transmission.

Thanks to the HDR, the detector uses less IR backlight at night and saves battery.

Intelligent false alarm filter

MotionCam Outdoor is equipped with two independent PIR sensors, the signals of which are analyzed by a two-step LISA algorithm. When both sensors detect motion, LISA performs correlation and spectral analysis of the signals, which helps to instantly distinguish real threats from interferences.

Correlation analysis

Whenever MotionСamOutdoor detects motion, LISA analyses and compares signal forms from two sensors in real-time. If forms are similar, the alarm is activated.

Spectral analysis

When both sensors detect motion, but the correlational analysis doesn’t identify enough similarities, LISA compares frequency components in the signals of both sensors.

Multilevel anti-sabotage protection

MotionCam Outdoor can not be unnoticeably disabled even if the system is disarmed. The detector is equipped with masking sensors reacting to hindering, covering and painting the lens.

It will take the hub less than a minute¹ to detect the loss of communication with the detector and inform a central monitoring station and users about the problem. The fact that MotionCam Outdoor was dismantled will become known instantly.

• Anti-masking system
• Notifications about detachment
• Configurable detector ping interval
•  

Effective security in any weather

MotionCam Outdoor resists the heat up to +60°С and withstand the cold down to −25°С. And to protect the sensors of the anti-masking system from rain and snow, we included a special hood.

• Efficiency in heat and cold
• IP55 enclosure protection
• Bundled hood to protect from rain and snow
•  

Uncompromising communication reliability

MotionCam Outdoor uses two secure radio protocols simultaneously: Jeweller and Wings. Radio protocols work independently of each other and each is focused on its own function. Jeweller transmits alarms in 0.15 seconds, and thanks to Wings, the first shot from the site will be in the app in less than 9 seconds².

The radio signal range is sufficient to install the detector where it will be most effective. And up to 3 years of battery life minimizes maintenance efforts.

• Two-way communication at a distance of up to 1,700 meters
• Photo delivery in less than 9 seconds
• Up to 3 years of battery life
•  

Less manual labor. More settings in the app.

The process of connecting and configuring MotionCam Outdoor saves installation engineers time in the best possible way. To add a detector to the system, all you have to do is scan the QR code with the Ajax app, assign a name and a room to it. Configure the device in the app in real time,test detection zones and communication. If necessary, the detector can be disabled or its system parameters can be reconfigured remotely, without visiting the site.

• Connecting - Adding to the security system via QR code
• Installation - Mounting using SmartBracket without disassembling the body
• Set up - Configuring in the app